Lining Drinking Water Tanks with Polyurea — Engineering Guide to Hot-Spray Linings

KNOWLEDGE · CASE STUDY

Lining Drinking Water Tanks with Polyurea

Engineering guidance for seamless, certified potable-water tank linings with Pure Polyurea Rayston — WRAS BS6920 compliant, CE EN-1504-2.

SYSTEM: Pure Polyurea Rayston APPLICATION: Potable / drinking-water tanks CERT: WRAS BS6920 · EN-1504-2 · ETA 16/0148 · BBA 18/5582 BUILD-UP: Primer 0.2–0.4 mm → hot-spray 1.8–2 kg/m²

Author / Spec chip · Pure Polyurea Rayston · Potable reservoirs · Hot-spray lining

“Enclosed reservoirs need a seamless, WRAS-certified elastomeric barrier — primer plus hot-spray Polyurea Rayston, with no superfluous internal aliphatic topcoat.”

ENGINEERING NOTE · Polyurea Rayston system

01 · Challenge

Crack bridging, hydrostatic pressure, WRAS hygiene

Lining large-scale potable water containment structures demands a high-performance elastomeric barrier capable of bridging substrate cracks, withstanding continuous hydrostatic pressure, and complying strictly with public health standards.

The engineering objective is not a cosmetic coating, but a seamless, monolithic containment liner for enclosed reinforced concrete reservoirs — floor slab, vertical walls, expansion joints, plinths, and service pipe penetrations — without introducing unverified chemicals to the wet surface.

  • Corner details, floor-to-wall junctions, and penetrations must remain continuous.
  • Hygiene requires uncompromising WRAS BS6920 potable-water contact certification.
  • Substrate preparation must follow EN-1504-2 cohesion, moisture, and defect remediation rules.
Hot-spray polyurea application
Primer + membrane cross-section

02 · Solution

Primer + hot-spray Polyurea Rayston seamless membrane

Pure Polyurea Rayston is an aromatic pure polyurea with a controlled, moderate cure profile. The system build-up for enclosed tanks:

  1. Concrete primer at 0.2–0.4 mm DFT — consolidates the substrate and anchors the membrane (Rayston Epoxy 100 / humidity-tolerant primer as required).
  2. Hot-sprayed pure polyurea at 1.8–2 kg/m² (~1.9–2 mm) via plural-component equipment (~65–75°C, ≥140 bar).
  3. No internal aliphatic topcoat — enclosed reservoirs have no UV exposure; Polyurea Rayston is WRAS-certified for direct potable immersion.

Open the technical data sheet or coverage calculator.

“Because enclosed concrete reservoirs lack ultraviolet exposure, an aliphatic topcoat is intentionally excluded from the interior wet envelope — preserving a single monolithic containment liner.”

03 · Specs

Key specifications & certifications

1.8–2
kg/m² consumption
~2 mm
Nominal DFT
25 yr
BBA 18/5582 life
WRAS
BS6920 potable

Accreditation

Site QA: track consumption weight alongside ultrasonic DFT. Substrate pull-off ≥1.5 N/mm²; moisture <4% for standard epoxy primers (up to 8% with humidity primer). See TDS #13 · Pure Polyurea Rayston.

System checklist

  • Abrasive blast / grind per EN-1504-2; remediate defects before spray
  • Primer DFT 0.2–0.4 mm matched to porosity / moisture
  • Hot-spray Polyurea Rayston 1.8–2 kg/m² continuous membrane
  • Omit internal aliphatic topcoat in enclosed tanks
  • Do not conflate Polyurea Rayston certifications with Impermax Aqua 2K

Cold-applied alternative where reactor access is impractical: Impermax Aqua 2K (≥2 kg/m², CE EN-1504-2, Directive 98/83/EC). See also drinking-water reservoirs.

04 · Results

Compliant potable lining — monolithic security

A correctly specified Polyurea Rayston lining delivers:

  • Public health safety — WRAS BS6920 confirms the cured liner does not leach toxic metals, promote microbiological growth, or impart taste/odor.
  • Structural concrete protection — CE EN-1504-2 crack-bridging and impermeability under hydrostatic head.
  • Proven durability — BBA 18/5582 independent 25-year service-life assessment.
  • Monolithic security — hot spray eliminates laps, seams, and fasteners that drive sheet-membrane failures.

Specification summary: EN-1504-2 surface prep → primer 0.2–0.4 mm → Polyurea Rayston 1.8–2 kg/m² (~1.9–2 mm) → no internal aliphatic topcoat for enclosed potable tanks. Contact an expert · Documents.

Resources

Next steps

Calculator

Estimate consumption for Pure Polyurea Rayston tank lining coverage and build-up.

Documents / TDS

Technical data sheet for Pure Polyurea Rayston — CE, ETA, BBA, WRAS.

Pure Polyurea Rayston

Product specification, system build-up, and approvals on the products page.

Contact an expert

Talk to Krypton Chemical technical team about potable-tank lining design.

Contact an expert

Newsletter

Get technical updates on waterproofing, flooring, and certified lining systems.

Or contact the technical team via the site contact form.

Scroll to Top